003 File Manager
Current Path:
/usr/src/sys/contrib/device-tree/Bindings/leds
usr
/
src
/
sys
/
contrib
/
device-tree
/
Bindings
/
leds
/
📁
..
📄
ams,as3645a.txt
(2.44 KB)
📁
backlight
📄
common.txt
(38 B)
📄
common.yaml
(7.81 KB)
📄
cznic,turris-omnia-leds.yaml
(2.17 KB)
📁
irled
📄
leds-aat1290.txt
(2.86 KB)
📄
leds-an30259a.txt
(1.33 KB)
📄
leds-aw2013.yaml
(1.86 KB)
📄
leds-bcm6328.txt
(8.25 KB)
📄
leds-bcm6358.txt
(2.97 KB)
📄
leds-class-multicolor.yaml
(1.22 KB)
📄
leds-cpcap.txt
(939 B)
📄
leds-cr0014114.txt
(1.37 KB)
📄
leds-el15203000.txt
(1.69 KB)
📄
leds-gpio.yaml
(2.04 KB)
📄
leds-is31fl319x.txt
(1.63 KB)
📄
leds-is31fl32xx.txt
(1.14 KB)
📄
leds-ktd2692.txt
(1.65 KB)
📄
leds-lm3532.txt
(3.59 KB)
📄
leds-lm3601x.txt
(1.34 KB)
📄
leds-lm36274.txt
(2.18 KB)
📄
leds-lm3692x.txt
(1.84 KB)
📄
leds-lm3697.txt
(2.03 KB)
📄
leds-lp55xx.txt
(4.26 KB)
📄
leds-lp55xx.yaml
(5.57 KB)
📄
leds-lp8860.txt
(1.26 KB)
📄
leds-lt3593.txt
(1.13 KB)
📄
leds-max77650.yaml
(1.03 KB)
📄
leds-mt6323.txt
(1.62 KB)
📄
leds-netxbig.txt
(2.3 KB)
📄
leds-ns2.txt
(1.05 KB)
📄
leds-pca9532.txt
(1.31 KB)
📄
leds-pca955x.txt
(1.88 KB)
📄
leds-pm8058.txt
(1.96 KB)
📄
leds-powernv.txt
(613 B)
📄
leds-pwm.txt
(1.36 KB)
📄
leds-sc27xx-bltc.txt
(993 B)
📄
leds-sgm3140.yaml
(1.42 KB)
📄
leds-spi-byte.txt
(1.25 KB)
📄
leds-tlc591xx.txt
(786 B)
📄
leds-trigger-pattern.txt
(1.96 KB)
📄
pca963x.txt
(1.44 KB)
📄
register-bit-led.txt
(2.3 KB)
📄
rohm,bd71828-leds.yaml
(1.42 KB)
📄
tca6507.txt
(1.01 KB)
📄
trigger-source.yaml
(646 B)
Editing: leds-netxbig.txt
Binding for the CPLD LEDs (GPIO extension bus) found on some LaCie/Seagate boards (Example: 2Big/5Big Network v2, 2Big NAS). Required properties: - compatible: "lacie,netxbig-leds". - gpio-ext: Phandle for the gpio-ext bus. Optional properties: - timers: Timer array. Each timer entry is represented by three integers: Mode (gpio-ext bus), delay_on and delay_off. Each LED is represented as a sub-node of the netxbig-leds device. Required sub-node properties: - mode-addr: Mode register address on gpio-ext bus. - mode-val: Mode to value mapping. Each entry is represented by two integers: A mode and the corresponding value on the gpio-ext bus. - bright-addr: Brightness register address on gpio-ext bus. - max-brightness: Maximum brightness value. Optional sub-node properties: - label: Name for this LED. If omitted, the label is taken from the node name. - linux,default-trigger: Trigger assigned to the LED. Example: netxbig-leds { compatible = "lacie,netxbig-leds"; gpio-ext = &gpio_ext; timers = <NETXBIG_LED_TIMER1 500 500 NETXBIG_LED_TIMER2 500 1000>; blue-power { label = "netxbig:blue:power"; mode-addr = <0>; mode-val = <NETXBIG_LED_OFF 0 NETXBIG_LED_ON 1 NETXBIG_LED_TIMER1 3 NETXBIG_LED_TIMER2 7>; bright-addr = <1>; max-brightness = <7>; }; red-power { label = "netxbig:red:power"; mode-addr = <0>; mode-val = <NETXBIG_LED_OFF 0 NETXBIG_LED_ON 2 NETXBIG_LED_TIMER1 4>; bright-addr = <1>; max-brightness = <7>; }; blue-sata0 { label = "netxbig:blue:sata0"; mode-addr = <3>; mode-val = <NETXBIG_LED_OFF 0 NETXBIG_LED_ON 7 NETXBIG_LED_SATA 1 NETXBIG_LED_TIMER1 3>; bright-addr = <2>; max-brightness = <7>; }; red-sata0 { label = "netxbig:red:sata0"; mode-addr = <3>; mode-val = <NETXBIG_LED_OFF 0 NETXBIG_LED_ON 2 NETXBIG_LED_TIMER1 4>; bright-addr = <2>; max-brightness = <7>; }; blue-sata1 { label = "netxbig:blue:sata1"; mode-addr = <4>; mode-val = <NETXBIG_LED_OFF 0 NETXBIG_LED_ON 7 NETXBIG_LED_SATA 1 NETXBIG_LED_TIMER1 3>; bright-addr = <2>; max-brightness = <7>; }; red-sata1 { label = "netxbig:red:sata1"; mode-addr = <4>; mode-val = <NETXBIG_LED_OFF 0 NETXBIG_LED_ON 2 NETXBIG_LED_TIMER1 4>; bright-addr = <2>; max-brightness = <7>; }; };
Upload File
Create Folder