File Manager

003 File Manager

Current Path: /usr/src/sys/contrib/device-tree/Bindings/ata

usr / src / sys / contrib / device-tree / Bindings / ata /

📁 ..
📄 ahci-ceva.txt(2.59 KB)
📄 ahci-da850.txt(645 B)
📄 ahci-dm816.txt(790 B)
📄 ahci-fsl-qoriq.txt(768 B)
📄 ahci-mtk.txt(2.01 KB)
📄 ahci-platform.txt(2.42 KB)
📄 ahci-st.txt(1.2 KB)
📄 allwinner,sun4i-a10-ahci.yaml(928 B)
📄 allwinner,sun8i-r40-ahci.yaml(1.35 KB)
📄 apm-xgene.txt(2.23 KB)
📄 atmel-at91_cf.txt(534 B)
📄 brcm,sata-brcm.txt(1.1 KB)
📄 cavium-compact-flash.txt(911 B)
📄 cortina,gemini-sata-bridge.txt(2.01 KB)
📄 exynos-sata.txt(945 B)
📄 faraday,ftide010.yaml(1.97 KB)
📄 fsl-sata.txt(897 B)
📄 imx-pata.txt(389 B)
📄 imx-sata.txt(1.34 KB)
📄 marvell.txt(567 B)
📄 nvidia,tegra124-ahci.txt(1.46 KB)
📄 pata-arasan.txt(988 B)
📄 pata-common.yaml(1.39 KB)
📄 qcom-sata.txt(1.42 KB)
📄 renesas,rcar-sata.yaml(1.8 KB)
📄 sata-common.yaml(1.35 KB)
📄 sata_highbank.yaml(2.47 KB)

Editing: qcom-sata.txt

* Qualcomm AHCI SATA Controller

SATA nodes are defined to describe on-chip Serial ATA controllers.
Each SATA controller should have its own node.

Required properties:
- compatible		: compatible list, must contain "generic-ahci"
- interrupts		: <interrupt mapping for SATA IRQ>
- reg			: <registers mapping>
- phys			: Must contain exactly one entry as specified
			  in phy-bindings.txt
- phy-names		: Must be "sata-phy"

Required properties for "qcom,ipq806x-ahci" compatible:
- clocks		: Must contain an entry for each entry in clock-names.
- clock-names		: Shall be:
				"slave_iface" - Fabric port AHB clock for SATA
				"iface" - AHB clock
				"core" - core clock
				"rxoob" - RX out-of-band clock
				"pmalive" - Power Module Alive clock
- assigned-clocks	: Shall be:
				SATA_RXOOB_CLK
				SATA_PMALIVE_CLK
- assigned-clock-rates	: Shall be:
				100Mhz (100000000) for SATA_RXOOB_CLK
				100Mhz (100000000) for SATA_PMALIVE_CLK

Example:
	sata@29000000 {
		compatible = "qcom,ipq806x-ahci", "generic-ahci";
		reg = <0x29000000 0x180>;

interrupts = <0 209 0x0>;

clocks = <&gcc SFAB_SATA_S_H_CLK>,
			 <&gcc SATA_H_CLK>,
			 <&gcc SATA_A_CLK>,
			 <&gcc SATA_RXOOB_CLK>,
			 <&gcc SATA_PMALIVE_CLK>;
		clock-names = "slave_iface", "iface", "core",
				"rxoob", "pmalive";
		assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
		assigned-clock-rates = <100000000>, <100000000>;

phys = <&sata_phy>;
		phy-names = "sata-phy";
	};

003 File Manager

Editing: qcom-sata.txt

Upload File

Create Folder