003 File Manager
Current Path:
/usr/src/sys/contrib/device-tree/Bindings/mux
usr
/
src
/
sys
/
contrib
/
device-tree
/
Bindings
/
mux
/
📁
..
📄
adi,adg792a.txt
(1.93 KB)
📄
adi,adgs1408.txt
(1.28 KB)
📄
gpio-mux.txt
(1.46 KB)
📄
mux-controller.txt
(4.65 KB)
📄
reg-mux.txt
(2.57 KB)
Editing: reg-mux.txt
Generic register bitfield-based multiplexer controller bindings Define register bitfields to be used to control multiplexers. The parent device tree node must be a device node to provide register r/w access. Required properties: - compatible : should be one of "reg-mux" : if parent device of mux controller is not syscon device "mmio-mux" : if parent device of mux controller is syscon device - #mux-control-cells : <1> - mux-reg-masks : an array of register offset and pre-shifted bitfield mask pairs, each describing a single mux control. * Standard mux-controller bindings as decribed in mux-controller.txt Optional properties: - idle-states : if present, the state the muxes will have when idle. The special state MUX_IDLE_AS_IS is the default. The multiplexer state of each multiplexer is defined as the value of the bitfield described by the corresponding register offset and bitfield mask pair in the mux-reg-masks array. Example 1: The parent device of mux controller is not a syscon device. &i2c0 { fpga@66 { // fpga connected to i2c compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", "simple-mfd"; reg = <0x66>; mux: mux-controller { compatible = "reg-mux"; #mux-control-cells = <1>; mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ }; }; }; mdio-mux-1 { compatible = "mdio-mux-multiplexer"; mux-controls = <&mux 0>; mdio-parent-bus = <&emdio1>; #address-cells = <1>; #size-cells = <0>; mdio@0 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; mdio@8 { reg = <0x8>; #address-cells = <1>; #size-cells = <0>; }; .. .. }; mdio-mux-2 { compatible = "mdio-mux-multiplexer"; mux-controls = <&mux 1>; mdio-parent-bus = <&emdio2>; #address-cells = <1>; #size-cells = <0>; mdio@0 { reg = <0x0>; #address-cells = <1>; #size-cells = <0>; }; mdio@1 { reg = <0x1>; #address-cells = <1>; #size-cells = <0>; }; .. .. }; Example 2: The parent device of mux controller is syscon device. syscon { compatible = "syscon"; mux: mux-controller { compatible = "mmio-mux"; #mux-control-cells = <1>; mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ <0x3 0x40>, /* 1: reg 0x3, bit 6 */ idle-states = <MUX_IDLE_AS_IS>, <0>; }; }; video-mux { compatible = "video-mux"; mux-controls = <&mux 0>; #address-cells = <1>; #size-cells = <0>; ports { /* inputs 0..3 */ port@0 { reg = <0>; }; port@1 { reg = <1>; }; port@2 { reg = <2>; }; port@3 { reg = <3>; }; /* output */ port@4 { reg = <4>; }; }; };
Upload File
Create Folder